China industrial automation switching valve Manufacturer, Supplier, Factory

GN19-12(C) indoor HV disconnect switch applies to power system of rated voltage 12kV, AC 50/60Hz. It is equipped with CS6-1 manual-operating mechanism and is used to break and make circuit under no-load. There are additional pollution type, high-altitude type and power indicating type. It is made as per IEC 62271-102. The isolating switch of this series is equipped with a CS6-1 manual operating mechanism (the isolating switch with a panel has its own conjoined operating mechanism).   This series of isolating switches is a three-pole type, which consists of a chassis, a rotating shaft, a lever, a porcelain pillar insulator, a knife and a wiring board. The rotating shaft is arranged on the bottom frame, on which three pairs of levers are welded, and the levers pass through the pull rod porcelain insulator and the knife necklace. The rotating shaft extends out of the base frame, and any section of the rotating shaft can be connected with the operating mechanism.   Type C is through the wall. Among them, C1 means that the rotation is on the side through the wall; C2 means that the disconnection is on the side through the wall; C3 means that both sides are on the side through the wall.

Product Introduction: Electrical Switchgear Handle The Electrical Switchgear Handle is a crucial component designed to provide efficient operation and control of electrical switchgear systems. Crafted from high-quality materials, these handles are engineered to ensure durability, reliability, and ease of use in various applications, including industrial, commercial, and utility environments.

The ZN12-24 vacuum circuit breaker is an indoor high-voltage switchgear with a rated voltage of 24kV and three-phase AC 50Hz.which introduced the technology from German company， Its operating mechanism is a spring energy storage type, which can be operated by AC or DC, or manually. This circuit breaker is a reinforced insulation type, which meets the requirements of the use environment in Class II polluted areas. This circuit breaker has simple structure, strong breaking capacity, long life, complete operation functions, no explosion hazard, simple maintenance, suitable for control or protection switch of power plant, substation and other transmission and distribution systems, especially suitable for breaking important loads and frequently operated places. This product is in accordance with related requirement of GB1984, JB3855, DL403 and IEC standards.

SOLH HFY Y-type pivot swing pneumatic gripper serves as a cost-effective interchangeable alternative to SMC MHC2. Driven by single piston pivot linkage with lever torque amplification. Two variants are offered: double acting HFY and single acting normally open HFTY. Swing range reaches +30°/-10° with total effective swing angle around 40°. Built-in adjustable throttle valves enable independent speed regulation for opening and closing, and repeat positioning accuracy achieves ±0.02 mm. Bore sizes cover 6/10/16/20/25/32 mm. Three mounting surfaces (bottom, side, rear) are available. Built-in magnetic rings are compatible with CMSH and DS1-G magnetic switches for limit signal feedback. It is ideal for outer wrapping gripping of round, curved and irregular miniature parts under confined installation space and high-frequency light-load handling conditions. During selection, note that clamping torque decreases with extended jaw overhang; a safety factor ≥1.5 is required for load verification. Compared with original MHC2, HFY features slightly narrower swing angle yet supports three-side mounting with superior cost performance. Original MHC2 is recommended if wider swing range or power-off normally closed holding function is required.

SOLH CP96S tie rod profile cylinder complies with ISO15552 and VDMA24562 standards, fully interchangeable with original CP96S series. Designed with dual buffer system combining adjustable air cushion and rubber pad, it achieves low noise and mild impact under high-speed & high-frequency reciprocation at 50~1000mm/s. The built-in tie-rod aluminum barrel is 15% lighter than conventional tie rod cylinders with high rigidity and excellent offset load resistance. Variants include single rod standard type and CP96SD anti-torsion double rod model. Built-in magnetic ring optional for M9B/A93 sensors; high temperature and stainless steel piston rod versions available. Bore φ32~125mm, customized stroke up to 2000mm. Widely used on machine tools and heavy-duty packaging automation for global equipment replacement.

Our company offers top-quality Switchgear Primary Plug-in Shields, essential for protecting critical electrical connections in switchgear systems. These shields are designed to ensure secure, reliable operation by preventing accidental contact and protecting against electrical faults. Crafted from durable materials, our plug-in shields provide excellent insulation and safety, enhancing the overall reliability of your switchgear. With a focus on innovation and precision, our products meet the highest industry standards, offering long-lasting performance and superior protection for your electrical systems. Trust our plug-in shields for dependable, effective safeguarding in your switchgear applications.