China Switchgear 8mm Square Lock Core Manufacturer, Supplier, Factory

Switchgear Inter-Phase Barrier: Product Details and Applications The Switchgear Inter-Phase Barrier is a critical component designed to enhance safety and performance in electrical switchgear systems. This barrier effectively separates electrical phases within a switchgear assembly, preventing unintentional short circuits and ensuring reliable operation. Constructed from high-quality insulating materials, the inter-phase barrier is capable of withstanding high voltage and thermal stress, making it suitable for various demanding environments.

Auxiliary Contact Switch The Auxiliary Contact Switch is a switch used in electrical equipment to extend the signal transmission function, assisting in the condition detection of main circuit equipment and providing additional switching signals during signal transmission. It acts as an auxiliary device to the main switch, providing additional contact signals to meet complex electrical control and indication requirements. Used to feedback, control, protect or indicate the status of a system, especially in automation and monitoring systems, plays a vital role. The auxiliary switch consists of a set of normally open (NO) and normally closed (NC) contacts that are synchronized with the state of the main switchgear. When the main device is operating, the contact of the auxiliary switch will be opened or closed according to the operating state of the device, thereby transmitting the signal to the control system or indicating device.

VSG-C/12 type Side installation Indoor high voltage vacuum circuit breaker used spring to storage energy. The operating mechanism can be operated by two ways, by manual and electromotive operation, The characteristics is according with GB1984-2003 High Voltage AC Circuit Breaker, JB3855-1996 3.6-4.5KV Indoor AC High Voltage AC Circuit Breaker and IEC standard 62271-100:200162271-100:2001 High Voltage AC Circuit Breaker. VSG-12C indoor high-voltage side-mounted vacuum circuit breaker is an indoor and outdoor switchgear for 12kV power system. Loads of different natures, frequent operations, and occasions where short-circuit current is broken multiple times. The product adopts a new type of circuit breaker operating mechanism, and the primary part of VSG-12 can use international brand solid-sealed poles to seal the vacuum interrupter and the main conductive circuit parts into a whole to protect the interrupter from collision, dust and condensation. It has strong environmental adaptability, greatly reduces operation and maintenance costs, and truly realizes the maintenance-free one-time part of the product and less maintenance of the operating mechanism. Perform frequent operations or break short-circuit current multiple times; the mechanical life can be up to 30,000 times, and the full-capacity short-circuit current breaking times can reach 50 times

GN19-12(C) indoor HV disconnect switch applies to power system of rated voltage 12kV, AC 50/60Hz. It is equipped with CS6-1 manual-operating mechanism and is used to break and make circuit under no-load. There are additional pollution type, high-altitude type and power indicating type. It is made as per IEC 62271-102. The isolating switch of this series is equipped with a CS6-1 manual operating mechanism (the isolating switch with a panel has its own conjoined operating mechanism).   This series of isolating switches is a three-pole type, which consists of a chassis, a rotating shaft, a lever, a porcelain pillar insulator, a knife and a wiring board. The rotating shaft is arranged on the bottom frame, on which three pairs of levers are welded, and the levers pass through the pull rod porcelain insulator and the knife necklace. The rotating shaft extends out of the base frame, and any section of the rotating shaft can be connected with the operating mechanism.   Type C is through the wall. Among them, C1 means that the rotation is on the side through the wall; C2 means that the disconnection is on the side through the wall; C3 means that both sides are on the side through the wall.

At our company, we are dedicated to providing high-quality switchgear components. Our switchgear square bars are meticulously engineered from premium materials to ensure superior strength and durability. These bars are designed to deliver reliable performance and structural integrity in various electrical systems. With a commitment to precision and excellence, our company offers top-tier solutions that meet the highest industry standards.

The chassis lock plate is a critical component used in electrical systems to securely fasten and lock the chassis of switchgear or electrical panels in place. Designed for safety and stability, this plate ensures that the chassis remains securely positioned during installation, maintenance, or operation, preventing accidental movement and enhancing the overall reliability of the electrical equipment. Made from high-strength materials, the chassis lock plate is built to withstand the rigors of industrial environments and provide long-lasting performance. It is easy to install and can be integrated into various switchgear configurations, offering flexibility and compatibility with different types of equipment. Ideal for use in substations, control rooms, and industrial facilities, the chassis lock plate plays an essential role in protecting both personnel and equipment. Compliant with international safety standards, it offers peace of mind by ensuring the secure operation of electrical systems.