China Electrical Switchgear Locking Mechanism Manufacturer, Supplier, Factory

Roof seal strip The IP31 Roof Joint is a robust and highly reliable component designed for use in electrical switchgear installations. With an ingress protection rating of IP31, this joint ensures a high level of protection against dust and condensation, making it suitable for various environmental conditions.

LW-126 type outdoor high voltage alternating current sulfur hexafluoride circuit breaker (hereinafter referred to as the circuit breaker) is a kind of outdoor high-voltage switchgear equipment with three poles AC SOHzand it adopts SF6 gas as arc extinguishing and insulation medium. It can be used for the separation and combination of rated current and fault current, capacitor bank, and switching circuit, and it can also be used as aninterconnecting breaker so as to realize the control and protection of transmission lines and equipment, especially suitable for frequent operation.The circuit breaker is equipped with CT20 type spring operation mechanism.This circuit breaker complies with the requirements of IEC 62271-100. Lw36-126 3150-40 self-energized Ac high-voltage sulfur hexafluoride circuit breaker is an outdoor product, suitable for altitudes not exceeding 2,ooo meters (products can be designed for altitudes above 3,ooo meters), and the ambient temperature is not lower than -40°c. In the Ac 50Hz power grid with a maximum voltage of 126KV in areas with a pollution level no higher than Level Iv, it is used to cut off rated current, fault current or conversion lines to achieve power control.For system control and protection, it can also be used as a contact circuit breaker This product uses sF6 gas as arc extinguishing and insulating medium, adopts the most advanced self-energy arc extinguishing technology in the world, and is equipped with a new spring operating mechanism. It has the characteristics of long electrical life, low operating power, low noise, and high reliability., with its simple structure, small size and long maintenance cycle, it can completely replace the same type of imported products in the current process of oil-free and large-capacity power equipment.

The electrical chassis car is a versatile and essential component designed for the transportation and support of electrical switchgear and equipment within substations and industrial facilities. This chassis car provides a robust and mobile platform, enabling the easy movement of heavy electrical units for maintenance, installation, or testing purposes.Constructed from high-quality materials, the chassis car is designed for durability and stability, ensuring safe handling of equipment. Its ergonomic design allows for easy maneuverability, and it often features adjustable height options and locking mechanisms to secure the equipment in place during operation.The electrical chassis car is compatible with various switchgear configurations and can accommodate a wide range of electrical components, making it an invaluable tool for electrical professionals. Adhering to international safety standards, it enhances operational efficiency and safety in demanding electrical environments.

GN19-12(C) indoor HV disconnect switch applies to power system of rated voltage 12kV, AC 50/60Hz. It is equipped with CS6-1 manual-operating mechanism and is used to break and make circuit under no-load. There are additional pollution type, high-altitude type and power indicating type. It is made as per IEC 62271-102. The isolating switch of this series is equipped with a CS6-1 manual operating mechanism (the isolating switch with a panel has its own conjoined operating mechanism).   This series of isolating switches is a three-pole type, which consists of a chassis, a rotating shaft, a lever, a porcelain pillar insulator, a knife and a wiring board. The rotating shaft is arranged on the bottom frame, on which three pairs of levers are welded, and the levers pass through the pull rod porcelain insulator and the knife necklace. The rotating shaft extends out of the base frame, and any section of the rotating shaft can be connected with the operating mechanism.   Type C is through the wall. Among them, C1 means that the rotation is on the side through the wall; C2 means that the disconnection is on the side through the wall; C3 means that both sides are on the side through the wall.

FLN36-24D load break switch use SF6 gas as arc extinguishing and insulating medium. There are three work stations: opening, closing and grounding in the switch. It has small volume, installing easy-to -use, strong environmental adaptabiliy and other characterist. FLN36-12(24)D/630-20 Indoor AC High Voltage SF6 Load Break Switch and FLRN36-12(24)D/100-31.5 Indoor AC High Voltage SF6 Load Break Switch-Fuse Combination are used for the three-phase AC 50/60Hz RMU and terminal power station. The switches are suitable for protecting the 10kV, 24kV and 35kV power systems in load situations. The switch can switch off the on-load current, closed loop current, no-load transformer capacity and cable charging current. The switch with fuse combination can cut off any current when the current is in the range of the rated short-circuit breaking current. They are suitable for the RMU, combined transformer, etc.

Richge specializes in the design and manufacture of high-quality switchgear door handles. Our Switchgear Door Handle range features premium materials and advanced craftsmanship, ensuring superior durability and reliability. Whether for electrical equipment or other industrial applications, our handles provide stable operation and enhanced safety. With meticulous attention to technology and quality control, we are committed to offering innovative, durable, and cost-effective solutions to enhance your equipment's performance and longevity. Choose us for trusted products and professional support.