China Switchgear Component Spacers Manufacturer, Supplier, Factory

SOLH WR110 series is a compact brass water pressure regulator specially designed for industrial cooling water and process water pipelines. Adopting anti-scale and anti-corrosion brass construction, it fits tap water and general industrial water working conditions. With dual adjustable pressure ranges and a maximum working pressure of 0.8MPa, it features built-in overpressure relief for stable water pressure and pipeline protection. Equipped with a lockable knob, reserved gauge port and diverse mounting options, it delivers fast response and minor pressure fluctuation. It is widely used in machine tool cooling, laser equipment, water treatment, instrument water supply and industrial spraying circulation systems.

SOLH CJ1 ultra-miniature pin pneumatic cylinder is interchangeable with equivalent SMC models, offered in φ2.5 and φ4 bore sizes. φ2.5 is single acting spring return only, while φ4 supports both single acting and double acting versions. Slim and ultra-lightweight (2~3.5g), it features no built-in cushion for rapid response. The rod-side air port can be rotated ±90° to facilitate tubing layout. External threads on both ends enable direct axial fixing without extra brackets. It delivers thrust ranging from 0.64 to 6.3 N at 0.5 MPa, suitable for micro loads below 100 g to avoid impact damage to delicate tiny workpieces. NBR seals support oil-free operation for clean environment. Widely applied in short-stroke high-frequency push-pull tasks including 3C button durability testing, chip ejection, micro component positioning, precision instrument fine-tuning and miniature actuators for medical devices. A thrust safety factor of at least 50% is recommended during selection.

Guide rail for electrical switchgear is a mechanical structure for supporting, guiding and mounting switchgear components, mainly used in electrical equipment. The core goal of its design is to ensure the stability of the switchgear, accurate alignment and ease of subsequent maintenance and replacement. Rails are usually made of aluminum alloy or galvanized steel, with strong load carrying capacity and corrosion resistance. For special environments (such as wet or corrosive places), the rails will be made of anti-corrosion treatment or stainless steel. Common rail shapes include "C", "U" or "L" sections, designed to be compatible with many types of switchgear. In addition, the standard size of the guide rail conforms to international specifications, which facilitates the modular installation of the equipment. In order to cope with the harsh environment, the surface of the guide rail may be galvanized, electrophoretic coating and other treatments to improve corrosion resistance.

SOLH MG series stainless steel mini pneumatic cylinders are engineered in compliance with JIS industrial standards, offering cost-effective alternatives to SMC CM2 & CM3 series with full dimensional interchangeability for direct replacement and production line retrofitting. Constructed with SUS304 stainless steel barrel and piston rod paired with high-strength aluminum end caps, they deliver outstanding rust resistance against high humidity, dust, weak acid and weak alkali surroundings, perfectly suited for food, pharmaceutical and packaging automation. Rivet rolling crimping secures the barrel and end caps tightly for excellent anti-vibration stability during long-term high-frequency reciprocation. A complete lineup covers standard double-acting, spring single-acting power-off reset types, synchronous double-rod variants and upgraded models with manually adjustable air cushions to suppress impact and noise in high-speed cycles. Low-friction composite sealing with built-in oil storage grooves supports oil-free maintenance-free operation for over 8 million working cycles. Every unit comes pre-installed with a built-in magnetic ring compatible with SMC M9B and Airtac CS1-G sensors to realize real-time position feedback and PLC automated linkage control. Supported by steady mass production and adequate overseas spot inventory, these cost-efficient cylinders are widely deployed in medium-grade automated equipment operating in damp and mildly corrosive workshop environments.

General Introduction GW1 series outdoor high voltage disconnect switch is the high voltage switch equipment of composite structure, is suitable for outdoor 12kV 、24KV 、40.5KV. line net with voltage and no load, to make opening and close. With CS□type manpower operate machinery, can avoid earth line with power and composite flash-locks etc wrong operate. The operator is no need to put another earth line. Pollution-proof type isolate switch satisfy customer in filthy conduction area. It can solve the pollution of shed when it is working. The GW1 series outdoor high voltage isolator switch is designed for reliable and durable performance in high voltage power distribution systems. Available in 12KV, 24KV, and 40.5KV, and current ratings from 630A to 1250A, these switches are built to withstand harsh environmental conditions, including high pollution and severe weather. With compliance to international standards IEC62271-103 and DL/T 486-2010, they ensure safety and operational integrity. GW1 outdoor AC high voltage isolating switch is suitable for installation on the line of outdoor high voltage power distribution equipment, which is used to cut off the line and convert the line when the line has voltage and no load. User-friendly installation and maintenance are facilitated by manual or electric operation mechanisms. The GW1 series is suitable for various environments, including high altitudes and extreme temperatures, making it an ideal choice for secure electrical isolation in outdoor systems.

SOLH HFR pivot-linkage 180° wide-opening pneumatic gripper is driven by piston linkage to rotate jaws. Each jaw swings up to 90°, forming a straight line when fully opened to provide maximum clearance and eliminate mechanical interference during pick-and-place. Bore sizes cover 10/16/20/25/32 mm with purely double acting design. The -2°~-5° overclose angle ensures stable clamping. Three mounting surfaces (side, bottom, rear) are available; locating pin holes on the base improve assembly accuracy, and suffix-N through-hole mounting is optional. All models come with built-in permanent magnets and sensor grooves compatible with CMSH magnetic switches. Optimized dust-proof jaw structure and anti-friction metal separators deliver service life over 5 million cycles for moderately dusty workshop environments. Widely used for gripping and turnover of deep-cavity workpieces, large plastic housings and box materials. MHW2 gear-driven swing gripper can be considered for medium-load applications if extreme avoidance clearance is unnecessary. A minimum 30% safety margin must be reserved during torque calculation; extended jaw overhang greatly reduces effective clamping torque.