China Indoor Medium Voltage Breaker Manufacturer, Supplier, Factory

SOLH HFZ linear guide parallel pneumatic gripper is directly interchangeable with SMC MHZ2 series. It adopts dual-piston rack & pinion synchronous transmission integrated with ball linear guide for high rigidity and excellent offset load resistance. Three actuation variants are available: standard double-acting HFZ; single-acting normally closed HFSZ (spring holds workpiece when air cuts off); single-acting normally open HFTZ (spring releases workpiece upon air loss). Bore sizes range from 6 to 40 mm with repeat positioning accuracy ±0.01~±0.02 mm. Multiple mounting options include bottom tapping, side mounting and through-hole N type. Dual-side sensor grooves and built-in magnetic rings support M9 series magnetic switches for open/closed feedback. Suitable for external clamping and internal expanding gripping. Optional accessories include dust covers, high-temperature seals and NSF-H1 food-grade grease. Effective clamping force decreases with extended jaw overhang; a safety factor ≥1.5 is required during load calculation. Widely deployed on robot end effectors, 3C electronics, precision hardware, injection molding and packaging automation precision gripping stations, especially for applications requiring power-off safety hold or release and working conditions with lateral offset loads.

SOLH SY series pilot-operated 5-port solenoid valve is fully interchangeable with matching SMC valves, including SY3000 mini, SY5000 medium mainstream, SY7000 large and SY9000 extra-large models. It provides complete circuit options: 5/2 single/double coil and 5/3 three-position with center closed, center exhaust & center pressure supply functions. Standard 0.35W coils and optional 0.1W ultra-low power energy-saving coils generate little heat for continuous energization. Internal pilot version works 0.1~0.7 MPa, while external pilot variant supports -100kPa vacuum environment. The gap-sealed spool reaches up to 200 million switching cycles. Air ports are arranged on side, top and bottom for flexible tubing routing. Valves adopt plug-in snap design compatible with SS5Y manifold valve islands, enabling single-valve maintenance without disassembling the whole bank, with IP65 plug connector and IP67 manifold base rating. Optimized internal runners deliver around 80% higher flow than legacy valves, and built-in pilot filter mesh prevents spool stuck by dust. Widely used for cylinder directional switching and centralized pneumatic control in semiconductor, automotive welding, packaging and medical automation equipment.

SOLH 2W series 2/2-way normally closed fluid solenoid valve with solid brass body includes small orifice direct-acting 030/050 models and large bore pilot-operated 150~500 variants, designed for automatic on-off control of clean water, compressed air, cutting coolant, lubricating oil and weakly corrosive fluid pipelines. The direct-acting version realizes zero differential pressure startup with no minimum working pressure limit, features compact size, universal mounting orientation and millisecond high-frequency switching, ideal for low-pressure micro-flow branches, vacuum auxiliary water circuits and single-point cooling for small machine tools. The pilot-operated type requires a minimum 0.05MPa startup differential pressure, delivers ultra-large flow with low-power low-temperature-rise coils, suited for air compressor main drain lines, general assembly main spray water circuits and high-flow circulating pipelines for water treatment systems. Standard NBR nitrile rubber seals are equipped, with optional heat & acid resistant EPDM food-grade seals. Multiple international thread standards (PT/G/NPT) and full-range coil voltages (DC12/24V, AC24/110/220V) are available, supported by DIN plug sockets for cabinet wiring and IP65 waterproof wire leads for humid outdoor equipment. Heat-resistant coils allow 24-hour continuous energization without burnout. Selection guidelines: choose direct-acting type for pipelines with static pressure below 0.05MPa and micro single-point flow; select pilot-operated variant for G1/2 and above main headers with stable high-pressure large circulation. EPDM seal is mandatory for hot water, purified water and food-grade fluid media.

The Electric Grounding Switch for Switchgear is an essential safety feature in high-voltage power systems, allowing for secure grounding and isolation of electrical equipment during maintenance. Designed for voltage ratings from 12kV to 40.5kV, it offers robust short-circuit protection and reliable mechanical performance. Its streamlined design enables quick installation and straightforward operation, making it perfect for use in high-voltage switchgear and substations. Meeting stringent international safety standards, this grounding switch ensures dependable operation and enhances safety in various electrical applications.

SOLH MHF2 ultra-thin dual-piston linear guide parallel air gripper is fully interchangeable with equivalent SMC models. Its ultra-flat body height is only roughly one-third of MHZ2, effectively reducing bending moment at robot end effectors. Bore sizes range from 8 to 32 mm. It is purely double-acting with built-in throttle valves for speed adjustment. Each bore offers three stroke variants: D short, D1 medium and D2 long, with repeat positioning accuracy ±0.04~±0.05 mm. Four-sided sensor grooves enable multi-direction mounting including bottom tapping and through-hole installation; -F single-jaw fixed type is optional. Φ25/32 large sizes adopt recirculating ball guides for enhanced rigidity. Built-in magnetic rings work with M9B/M9N/M9P reed switches for position feedback. Ideal for height-restricted compact spaces, miniature linear modules, small robot EOAT, semiconductor and 3C precision assembly. During selection, jaw overhang length must be limited and bending moment verified with a safety factor ≥1.5.

Switchgear Seal Strip: Product Details and Applications The Switchgear Seal Strip is a crucial component designed to enhance the performance and longevity of electrical switchgear systems. Constructed from high-quality materials such as silicone, EPDM, or neoprene, this seal strip provides excellent resistance to environmental factors including moisture, dust, and temperature fluctuations. Its flexible design ensures a tight seal around doors and panels, effectively preventing the ingress of contaminants that can cause corrosion and electrical failures.