China Secondary Electrical Pin Insertion Manufacturer, Supplier, Factory

GN19-12(C) indoor HV disconnect switch applies to power system of rated voltage 12kV, AC 50/60Hz. It is equipped with CS6-1 manual-operating mechanism and is used to break and make circuit under no-load. There are additional pollution type, high-altitude type and power indicating type. It is made as per IEC 62271-102. The isolating switch of this series is equipped with a CS6-1 manual operating mechanism (the isolating switch with a panel has its own conjoined operating mechanism).   This series of isolating switches is a three-pole type, which consists of a chassis, a rotating shaft, a lever, a porcelain pillar insulator, a knife and a wiring board. The rotating shaft is arranged on the bottom frame, on which three pairs of levers are welded, and the levers pass through the pull rod porcelain insulator and the knife necklace. The rotating shaft extends out of the base frame, and any section of the rotating shaft can be connected with the operating mechanism.   Type C is through the wall. Among them, C1 means that the rotation is on the side through the wall; C2 means that the disconnection is on the side through the wall; C3 means that both sides are on the side through the wall.

SOLH I type single clevis joint for pneumatic cylinder rod end, low cost U clevis hinged connector with ±5° swing. Carbon steel / stainless construction, female thread M10×1.25 M36×2.0 matching 32-200 mm bore cylinders, pin hole φ10-36 mm. AirTAC/SMC/domestic naming compatible (F M10×1.25I, I 32, CA2 40 I). Ideal for push pull loads, linear guides and flipping mechanisms.

Switchgear Mechanism Block Product Background: Richge is equipped with advanced production facilities and technology , and our team consists of experienced engineers and technicians dedicated to providing high-quality products to our clients. We strictly adhere to international quality management system standards and implement comprehensive quality control processes. Each production stage undergoes rigorous inspection to ensure that every product meets the highest quality standards.

The Bottom Support Component BB70 is engineered for robust performance in electrical switchgear applications. Constructed from high-quality materials, it provides excellent structural integrity and durability. Designed to accommodate various switchgear systems, the BB70 offers precise alignment and stability for effective load distribution. Its features include adjustable height settings for versatility in installation, ensuring compatibility with different equipment configurations.

SOLH MHZ2 standard-stroke and MHZL2 long-stroke parallel air grippers are fully interchangeable with equivalent SMC models. Driven by symmetric dual pistons and precision linear guide rails for synchronous jaw movement, they deliver ultra-high repeat positioning accuracy of ±0.01mm with bore sizes 10/16/20/25 mm. Three actuation modes are available: D double acting for maximum clamping force and continuous mass production; S single-acting normally open, which automatically releases workpieces upon air cut to avoid crushing at hot stamping stations; C single-acting normally closed with spring holding force without air supply to prevent workpiece drop for overhead robot handling. A full range of interchangeable jaws (narrow, thin flat, side tapped for extended fixtures) and multiple body port layouts (standard side port, end side port, axial push-in port) are optional. Built-in magnetic rings work with M9BW reed switches to transmit open/closed position signals to PLC interlock systems. MHZ2 features short stroke and high cycle speed up to 180 cpm for tiny miniature parts, while MHZL2 adopts extended guide rails for wide opening stroke to handle deep-cavity molds and large thick plates. All jaws, fittings and sensors are cross-compatible between the two series. Widely deployed for PCB & chip sorting, precision hardware loading/unloading, packaging clamping and workpiece transfer at robot end effectors in 3C, hardware and packaging automation lines.

FN18 load switches and load switch-fuse combinations are high-voltage, high-performance load switches combining compressed-air arc extinguishing and gas-produced arc extinguishing. The combination of load switch and fuse combines the advantages of the load switch with those of the fuse to switch any load current up to the rated breaking current of the load switch, and to switch any overcurrent up to the rated short-circuit breaking current of the combination by means of the operation of the fuse and its impinger. It is used in three-phase power distributions of AC 50Hz rated voltage 12kv and rated current 630A Esp For power ring network in city net work construction improvement high-rise buildings and public facilities as an ideal product to protect package substation and transformer It has the features of advanced design simple operation impact structure smart appearance light weight complete function fast on-and off speed and high reliability.